designed specifically for off shore oil rigs

RUST GRIP - Coating for Harsh Environment Protection - RUSTGRIPRUST GRIP - Protective Non Slip Coating - RUSTGRIPRUST GRIP - Coating For Harsh Environment Protection - RUSTGRIP

6,750 psi Tensile strength equal to US Highway concrete!


RUSTGRIP (NS) ® is a one-part polyurethane coating that combines with atmospheric moisture to cure. Upon curing, RUSTGRIP (NS) ® provides a protective coating of superior adhesion, flexibility and abrasion/impact-resistance. It is resistant to chemical solvents and acid splash. Originally designed for metal surfaces, RUSTGRIP (NS) ® demonstrates excellent adhesion to wood, concrete, fiberglass and many other substrates.

RUSTGRIP (NS)® is designed for the encapsulation of and adherence to tightly-bonded surfaces of lead-based and other toxic paints as well as rusted surfaces. This unique ability is accomplished by the curing mechanism of the base polymer. The coating (having a low initial viscosity) wets the surface, then penetrates into the pores of the substrate where curing begins. RUSTGRIP (NS) ® actually becomes part of the substrate unlike a surface coating which just bonds on top. The polymer literally begins to swell, developing an interlocking network between the pores of the surface and the coating. RUSTGRIP (NS) ® is highly recommended as a base coat for SUPERTHERM ®. No pot life, no catalyzation, no two-part mixing. RUSTGRIP (NS) ® is not a sacrificial rust inhibitor such as a zinc enriched primer that will wear out over time but in fact a permanent rust proofing which is why it is a certified ( ASTM E1795 ) Biohazard Encapsulator.

® has also passed 15,000 hours of salt spray testing which are marine specifications and consequently has achieved DNV certification. Can substitute for zinc-rich primer requiring no white sandblasting. Can be applied over rusted surfaces after loose/flaking material is removed. High humidity quickens the dry / cure cycle.

The difference between a surface coating and RUSTGRIP (NS)! ®

A surface coating does not have the special solvent carrier to allow it to enter the pores of a substrate and carry the body of the coating into the pores with it. The surface coating will bite into anything above the pore area and adhere to the surface by attaching to any roughness. This works well in most areas until the surface of the coating is exposed to weathering and other elements over time allowing oxidation and acid rain to enter through its pin holes and begin the migration of corrosion.

RUST GRIP (NS) ® is made with special solvent carriers that allow the coating to penetrate into the pores carrying the body of the coating with it. Once the body of the coating is in the pores, it begins to absorb the moisture from the atmosphere and gases itself or does a microscopic swell inside the pores that anchors it into the metal or any other surface. This action does allow the coating to become part of the actual surface with is different than all other industrial coatings. Also, its high molecular weight allows the coating to become extremely tough. Being an aromatic urethane in nature, it is already extremely resistant to acids. Its non-leafing metallics allow an encapsulation of the surface and adds additional toughness and UV control to its surface.

* Solids: By weight 70.5% / By Volume 62%
* Bridges - two coats by brush or roller - 8 mils wet; 4 mils dry
* Cure time at 70°F (21°C): 2 hours to touch.
Overcoat with other coatings immediately after surface is dry to the touch to achieve proper adhesion.
Higher temperatures and humidity will shorten cure times, lower temperatures will slow curing.
* Lead and Chromate free
* Cures by reacting to moisture in the air
* Weight: 9.5 lbs. per gallon
* Surface Tensile Strength: 6,780+ psi
* Vehicle Type: Aromatic polyurethane
* Shelf Life: up to 3 years (unopened) under appropriate storage conditions (see MSDS)
* VOC Level: 400 grams/liter
* Impact Resistance: 200+ psi front/160+ psi back
* Can withstand temperatures up to 300°F.

•USDA approved ( safe around food )
•Lead & chromite free
•Patented Biohazard Encapsulation ( ASTM E1795 )
•Outstanding Adhesion ( ASTM D3359 ) Coated over 18 coats of oil based paint, penetrating through all 18 coats and secured to the substrate
•Performed 20,000 Window Cycling tests equal to 54 years
•Not affected by acid splash
•Guards against all corrosions
•Subjected to - 350°F degrees nitrogen at Air Products Co. without effect
•Can withstand + 325°F degrees constant heat before the resins burn out
•Guards against all corrosions

Unless Superior Products provides a written warranty of fitness for a particular use, Superior Product's sole warranty is that the product, as supplied, will meet then current sales specifications and is specific only to return of product found to be defective upon opening of container within one year. Customer's exclusive remedy and Superior's sole liability for breach of warranty is limited to refund of the purchase price or replacement of any product shown to be other than as warranted and Superior Products expressly disclaims any liability for incidental or consequential damage.

Aren't you tired of having to do repeated surface repair and maintenance?



Print this page